Guide :Exercise & Fitness : Treadclimber

The machine will quit wright after you start and

My bowflex treadclimber tc5000 machine will quit wright after it start and gives an error code ==L5.

Research, Knowledge and Information :


Machine Quilting Tips and Tricks - dummies


Machine Quilting Tips and Tricks. ... To start machine stitching: 1. ... When you reach a spot where you need to stop stitching, ...
Read More At : www.dummies.com...

Sewing Machine Troubleshooting - The Spruce


Learn basic troubleshooting for your sewing machine to save costly repair bills and start sewing again in no time. ... Sewing Machine Troubleshooting
Read More At : www.thespruce.com...

Steven Wright Quotes - Freese-Notis Weather Services


... do you start to think you're ... Now I have an extra xerox machine. -- Steven Wright. ... Steven Wright. I had to stop driving my car for a while ...
Read More At : www.weather.net...

Washing Machine Will Not Start - RemoveandReplace.com


Washing Machine Will Not Start ... I switch off main the switch for soaking clothes and after some time I start machine. ... Our washer just quit, ...
Read More At : removeandreplace.com...

How Long After Quitting Smoking Do Lungs Heal - HealthTap


... Dr. Dunner on how long after quitting smoking do ... The body is a self healing machine. The only thing you can do is attend ... How long after you quit ...
Read More At : www.healthtap.com...

The Wright Story


The Wright Story (You are here.) Down Wright Timeline An Unusual Childhood Career Choices Inventing The Airplane ... A Practical Flying Machine :
Read More At : www.wright-brothers.org...

How Do I Improve Lungs After Quitting Smoking - HealthTap


... Dr. Wartenberg on how do i improve lungs after ... The body is a self healing machine. The only thing you can do is attend ... How long after you quit ...
Read More At : www.healthtap.com...

CarveWright manual C SN 999


installation and start up costs. ... inoperative or unusable after a reasonable period of use ... of any CarveWright Machine. This warranty gives you specific ...
Read More At : www.carvewright.com...

The Wright Brothers | Inventing a Flying Machine


Inventing a Flying Machine; ... the Wright brothers conducted a program of aeronautical research and experimentation that led to the first successful powered ...
Read More At : airandspace.si.edu...

Suggested Questions And Answer :


The machine will quit wright after you start and


Had my TC5000 for a year and this is the first time this happened. I use it everyday. Googled "Bowflex Teadclimber error codes" and found this link  download.dfxi.com/supportdocs/AM/Bowflex/BFX_TC135_AM_2008.pdf which is a pdf manual.  I'm going to try this fix now, hope it works for you and me Here's what it says for ERR LS: Belts stop turning and “err LS” or “err OS” is displayed Calibration Re-calibrate machine using Owner’s Manual calibration procedure. Speed sensor 1. Cycle power off and on. 2. Put the machine in calibration mode (see Calibration procedure in Owner’s Manual) but do not start the calibration routine. 3. Remove right rear plastic cover to view LED diagnostics on control board. Caution: Machine is on. Current is active!! 4. Locate LED D on the motor controller board. LED may be lit or unlit. 5. Manually advance the treadle with your foot, and check if LED D is blinking. 6. If LED D is not blinking, then the speed sensor is not supplying a signal. Check that the speed sensor wire is plugged into the motor controller board, to the connection labeled “P1”. Check connection of speed sensor to jumper wire. Check speed sensor adjustment (use business card to set gap between sensor and pulley). If LED D still does not flash replace sensor. I/O cables If LED D is flashing when the belts are turning but err LS or OS persists check connections and for signs of visible damage to any of the three I/O cables. If no damage, check continuity using a multi-meter. If a multi-meter is not available contact customer service for replacement cables and further assistance. Mike
Read More At : Treadclimber...

Treadclimber error code H-23


Answer from bowflex service line. H 23 means "no tac signal". which means, a signal cable is loose or disconnected. OR the motor needs replacing...estimated cost $350 Canadian.
Read More At : Exercise & Fitness...

Nordic track troubleshoot


Seem like you're running the controller too hot. If it runs ok when no one is on it, your walking belt and deck is probably bogging down causing over current
Read More At : Exercise & Fitness...

Bowflex Treadclimber TC20 error messages


Dear Sir:This is a common error in this kind of machine. You must call to the company bowflex, and claim the problem. The hardware design is defective, they will replace. However you will the same problem, if you do not act right now.God bless you
Read More At : TreadClimber TC20...

My machine is making a grinding sound (medal to medal) when i use the machine. if i lock it and only use treadmilll it is ok. it seams to happen more and more. i really grinds if i stand on step offs. don't know what happened it just started. bowflex treadclimber 5000


You'll need inspect the movable areas of your unit by hand something may have come loose or see if their is any excessive lateral play could be worn or cracked bushings. Have some else help you by stepping off on either side to see where the sound more prominent. Unfortunately it a process of elimination good luck!
Read More At : Treadclimber...

E-1 message I was using the machine recently and towards the end of my workout the belts sped up uncontrollably. I went to start the machine recently and the belts do not move. After 10 seconds the E1 message appears. I have a brand new speed sensor and calibrated it with a credit card. Any ideas what else it could be?


In some way the signal from the speed sensor is not making it to the control board. Trace the wire from the sensor to the control board and make sure there are no cuts or crimps. There is also an unused wire on the TC1000 that looks exactly like the speed sensor wire but doesn't connect to anything (it is used on higher models), make sure you are not connecting to that wire.
Read More At : TC1000 Treadclimber...

My Uncle gave me a Horizon T605 treadmill and the


Horizon rct 7.6 , safety key off , replaced ,key.reed switch and board , still says safety key off ?? spoke to horizon several times and repair techs as well ,it can only be 1 of those 3 items , all switch & key tested good , must be a faulty new board ?? could it be anything else ??
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0493 seconds