Guide :Exercise & Fitness : Bodyguard T200 Treadmill

Treadbelt not alligned

Theres a little gap on the right side of the belt. How do i move the belt a little to the right. I lost my manual. Thank you for your help.

Research, Knowledge and Information :

How to Align a Treadmill Walking Belt | Sportsmith Blog

How to Align a Treadmill Walking Belt . ... If the belt seems to be properly aligned, your work is done. If not, you may need to adjust further; ...
Read More At :

Non-aligned Synonyms, Non-aligned Antonyms |

Synonyms for non-aligned at with free online thesaurus, antonyms, and definitions. Dictionary and Word of the Day.
Read More At :

How To Adjust Treadmill Belt - Treadmill Repair - YouTube

Apr 07, 2013 · How To Adjust Treadmill Belt - Treadmill Repair RJ The Bike Guy. Loading ... How-To Align a Treadmill Belt Green Fitness Company treadmill saver ...

Belt Wont Stay Centered - Treadmill Doctor

SECTION 1 If the belt will not stay centered after making tracking adjustments: Check the roller for a plastic sleeve. Some treadmills come equipped with a plastic ...
Read More At :

Maintenance: Treadbelt Tensioning and Tracking | Landice ...

Maintenance: Treadbelt ... you change the alignment of the rear roller ... The treadbelt is not exactly centered on the Drive Roller because of the ...
Read More At :

All About Treadmill Belts – Installation & Maintenance

Treadmill belts can and do wear out and it’s not unusual that you’ll need to replace your belt after two years, or even a year with heavy use.
Read More At :

Why Does My Belt on My Treadmill Keep Sliding to One Side?

Nov 01, 2015 · If your treadmill belt starts running closer to either foot rail -- either right after you buy the treadmill or after steady use -- it's usually not a...
Read More At :

Adjusting Your Treadbelt | Fitness and Exercise Equipment ...

Adjusting Your Treadbelt ... then the right side of the treadbelt is not as tight as the left side. ... Foreign objects can cause alignment problems too: shoes, ...
Read More At :

Suggested Questions And Answer :

Pro-form treadmill belt binds - RTO Bodyguard T200 Treadmill

May need to be tightened
Read More At : Bodyguard T200 Treadmill...

I need a replacement board "microcomputer" for a Magellan Bodyguard Treadmill??

Please go to and buy iy otwww.doctortreadmill.comHappy New Year. God bless you
Read More At : Bodyguard T200 Treadmill...

Elevation Will NOT go down after the elevation calibration

Unplug unit and remove motor shroud if you are savvy with a multi meter then try these trouble shooting procedure: Perform and elevation calibration again, On the display, can you see numbers counting down and up and the treadmill is going up and down? If yes then the unit will proceed to work, if no when power is on, check on the lower board, on connector J5, do we have 5V DC between pin 1 & 3? If yes During Calibration, J5, between Pin 5 & 6, on the lower board, do we have 120V AC when treadmill is going up? If Yes During Calibration, J5, between Pin 4 & 6, on the lower board, do we have 120V AC when treadmill is going up? If Yes During Calibration, J5, between Pin 2 & 3, on the lower board, do we have DC voltage varying from 1.15 to 3.00? If any of the above is no then then the lower board will need replacing if all is yes then elevation motor needs replacing.
Read More At : Bodyguard T200 Treadmill...

Treadbelt not alligned

Hi, Most all treadmills use the same type of belt tracking, which is an allen screw adjustment on the rear tension bar. One on either side. You should have been provided an allen wrench with your treadmill, if not then use one of your own the proper size. Make the adjustment with the unit running at its slowest speed. Clockwise tightens the tension and will draw the belt. Good Luck, this should Fixya!
Read More At : Bodyguard T200 Treadmill...

Bodyguard T240 wont start

To use these instructions, you need to have a familiarity with electricity and a working knowledge of a voltage multimeter. With all of these tests, USE EXTREME CAUTION!!! Never let the voltage ground directly to any part of the treadmill or your leads ground while you are testing voltage.1) To begin, set your volt meter to AC volts. We are going to trace the power from the wall outlet through the treadmill to see where it ends.2) With the treadmill unplugged, test the wall outlet. You should have from 115 to 125 VAC. Optimally, you will have at least 120 VAC.3) Follow the power leads from the power cord to the lead ends. With the treadmill unplugged, connect your meter to the lead ends. Plug the treadmill in and check your reading. It should be the same as your reading from the wall outlet.4) Continue this process with the electrical system, following the leads, as they pass through, breakers, fuses, and the like.5) Where the power flow ends is where your problem is. Sometimes it will be in a bad connection, sometimes it will be in a shorted breaker or blown fuse, at times it may be as simple as a safety switch not working properly, or it may be a major problem with a component.6) In some cases, components work in tandem (i.e.- a controller may need a signal from the console computer to release voltage to the motor. TESTING FUSES, BREAKERS, WIRING, AND SWITCHES1) One of the most common problems with power outages is problems with fuses, breakers, wiring, or switches.2) If your treadmill is equipped with a safety switch, set your volt meter to continuity. Touch your test leads together to make sure you are getting a closed circuit. With the treadmill unplugged, back the leads off the safety switch, usually near the upper display computer. With the safety key out, test the switch. It should be open. Push the safety key in. Your circuit should be closed. If this tests ok, move to the next step.3) While testing for voltage, you can unplug your treadmill and test the fuses, breakers, and wiring harnesses. Sometimes a breaker may have shorted open and not tripped. Test these components individually. You want a closed circuit on all of them
Read More At : T240 Treadmill...

Treadmill buttons don't work right. TV won't turn off. Treadbelt won't run.

1) Try to reconnect the plug between console and pcboard very well. 2)Clean the contacts with special contact cleanear( radio schack or computer store) with carefully only the buttons, if you can open the cover better. 3) adjust the Sensor SWITHC. 4) Look for any wire loose, or making bad contact, or break wiring( continuity) test the fuse and breaker. If after you did those steps, and the problem persist, the console board is faulty.but first change the sensor switch, you must be shure after adjustment.
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.1193 seconds