Guide :Exercise & Fitness : Exercise & Fitness

Bogs down I have a Sportscraft tx 500 treadmill and when i go to walk on it , it slows way down and almost stops and if i get of it runs fine at the right speed. please help its just like new

Posted by Sarah Burgus on Feb 21, 2009

Research, Knowledge and Information :


Belt Slows Down or Bogs Down - Treadmill Doctor


Belt Slows Down or Bogs Down. ... The coast test is to get on the treadmill as the lowest incline setting and walk on the treadmill ... some people just crank down ...
Read More At : www.treadmilldoctor.com...

3 Easy Ways to Fix a Treadmill (with Pictures) - wikiHow


wiki How to Fix a Treadmill. ... is a that your treadmill is just not ... If you have the knob style that you turn to speed up/slow down, you probably need a new ...
Read More At : www.wikihow.com...

How to Troubleshoot a Treadmill That Stops Suddenly ...


Apr 30, 2015 · A treadmill that stops running ... When too much resistance occurs during a run or walk, the treadmill stops ... The best way to check the speed ...
Read More At : www.livestrong.com...

Reasons Why My Treadmill Belt Stops When I Step on It ...


May 10, 2015 · Reasons Why My Treadmill Belt Stops When I Step on It? ... run at a slow speed. If the belt runs normally then it is ... to just tighten up the ...
Read More At : www.livestrong.com...

Treadmill Reviews: August 2011


<<Sportcraft tx420 slows down | ... All the information you need about ProForm C500 Treadmill like treadmill reviews , please ... Xp crosswalk 500 --
Read More At : www.livestrong.com...

.... 3 May ...


http://treadmillreviewsreal.blogspot.com/2011/08/
Read More At : www.livestrong.com...

Introduction / Day 1 Thread : loseit - reddit.com


It was the first time she actually started calling me pretty and buying my new outfits so I just ... I have a long way to go, ... I would like to get back down to ...
Read More At : www.reddit.com...

About Checkpoint - tax.thomsonreuters.com


How can you quickly find the right amount or get up-to-speed on unfamiliar federal tax topics? NEW ... in a down-to -earth and concise ... have learned the hard way ...
Read More At : tax.thomsonreuters.com...

Meh Car Monday: Try And Recall The Hyundai XG350


A Meh car is an inert, noble gas, like argon, something that accomplishes its fundamental job ... which is just, ... its fundamental job while affecting almost ...
Read More At : jalopnik.com...

Suggested Questions And Answer :


This is a TS01 new fitness machine,recently I had to use the safety button and after that the screen is just blue now with no text etc, speed, heart rate nothing everything else works. Please can anyo


I have the same Tradmill when I turn it on makes bang noise and trips fuse box any1 no what's wrong with it cheers
Read More At : Exercise & Fitness...

Bogs down I have a Sportscraft tx 500 treadmill and when i go to walk on it , it slows way down and almost stops and if i get of it runs fine at the right speed. please help its just like new


Sounds like either the belt is loose or the belt/deck need to be lubed. To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.To lube the treadmill, use silicone spray and spray between the belt and deck on both sides. I hope this helps. Let me know if you have any other problems.
Read More At : Exercise & Fitness...

This is a adress that is shown my treadmill model : http://www.diaplasi.gr/oxide/cf_9010.html.


Please go under the HOOD motor and follow the steps for RUN the software calibration or go under the instr. manual and follow the steps how to enter the s. calibration.tHIS will be guide to easy diagnose, troubleshooting, and fix it. God bless you
Read More At : Exercise & Fitness...

Enginerring mode not working


Follow the next steps and fix it.God bless you The Steps for Newer Style Console Calibration 1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.) 2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed). 3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21. 4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools. 5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window. 6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window. 7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window. 8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window. 9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E." 10. Press ENTER. You should see "SS" or "55" in the console. 11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill. 12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own. 13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position. 14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use. 15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1504 seconds