Guide :Exercise & Fitness : Exercise & Fitness

TUNTURI 620p TREADMILL displays 51, or S1 WHEN TURNED ON , AND WILL NOT OPERATE. PLEASE SEND ANY INFORMATION TO HELP SOLVE THIS PROBLEM.

Posted by juliacraze on Feb 17, 2009

Research, Knowledge and Information :


Treadmill Review: 2011


... Help Solve This Problem · aerobic Technologies Treadmill Medicostride Treadmill . TUNTURI 620p TREADMILL displays 51, or S1 ... Treadmill Review – the ...
Read More At : treadmillreviewunreal.blogspot.ca...

The Messenger 10-10-09 by Sun Community News and Printing - issuu


Title: The Messenger 10-10-09, ... If you have any questions please contact the ... , many homeowners think the only way to solve this problem is to buy expensive ...
Read More At : issuu.com...

ufdc.ufl.edu


won't solve the problem. ... new configuration and any change is disturbing. It will: Please see VEDDER, 12A ... bus service will not operate on Sunday, July 3, ...
Read More At : ufdc.ufl.edu...

Adirondack Journal 10-03-09 by Sun Community News and ...


www.adirondack-journal.com. SATURDAY October 3, 2009. Celebrated author Paul Pines set for Willows reading event By Thom Randall [email protected] WARRENSBURG ...
Read More At : issuu.com...

Citrus County chronicle - University of Florida


I want to send information to the Chronicle: ... growing clout to help re-solve international disputes ... CITRUS COUNTY CHRONICLE New officers
Read More At : ufdc.ufl.edu...

Fundamental interaction


fundamental interaction gravity lorentz force magnetic ... Galileo Galilei experimentally determined that this was not the case — neglecting the friction due ...
Read More At : electromagnetism.gq...

Full text of "The Argonaut" - Internet Archive


Search the history of over 299 billion web pages on the Internet.
Read More At : www.archive.org...

M240 machine gun operators manual - dulimutihanikid182.cf


The bipod would eventually be relocated apart from the barrel in future M60 forms to help ease barrel changing. Though not the ... turned out, the US ... displays ...
Read More At : dulimutihanikid182.cf...

Suggested Questions And Answer :


TUNTURI 620p TREADMILL displays 51, or S1 WHEN TURNED ON , AND WILL NOT OPERATE. PLEASE SEND ANY INFORMATION TO HELP SOLVE THIS PROBLEM.


Solution: press and HOLD the button that says display above it and Reset below it untill you see the normal start up Screen and yoru good to go!
Read More At : Exercise & Fitness...

Technofit TS500i treadmill error code?? ( E1 & E2) please help!!!!!!!!!


Dear Sir:The error code E1or E2 coming from this reasons.1) Adjust the speed sensor, see the diagram attached, clean, and tight the connector wires.2) Test the main motor input voltages coming from the output from the main motor board.3) The main motor or motor board can be faulty or need repair.See my personal TIPS for HELP and guide you.sincerely. God bless you
Read More At : Exercise & Fitness...

I have problem with error 02??


Push and hold any two buttons, for about 30 seconds you might hear a beep or the screen will reset.,,,adrian
Read More At : Exercise & Fitness...

Hi, do you speak spanish? I have a treadmill xterra3.0 but when i was assembled to use it...it marks error 6 . What it could be.... I have contact the proveedor and they send me the master card ( i


SO SORRY NO SPANISH little japanese tho
Read More At : Exercise & Fitness...

Problem with my Rogerblack treadmill


I av gold treadmill model ag10302 and need 2 get mains lead
Read More At : Exercise & Fitness...

Itook my startrac pro s treadmill apart to move it from downstairs to upstairs in house. The wire running from bottom circuit board to display console got strained and bent two condensers on circuit board,Had these replaced.Treadmill now runs for 17 seconds at idle speed,3 seconds if you try to increase speed and then stops.Displays message"CHECK SPEED SYSTEM".Had speed sensor at flywheel and wire which was strained tested,which were both o.k.I Took cover off back of display console,nothing seems to be bent or broken that i can see,i also followed the steps for recalibrating the speed to no avail either.Before i had the condensores replaced the machine would not work at all it just made clicking noises.thats all the info. i can give. Please please HElp!!!Since posting this problem i've had some very good advise from one of your experts (blueextc) but i cant seem to make contact with him,in order to carry out his advise i need to enter maintenence mode and there in lies my latest problem,i cant gain access.I've checked all connections and nothing appears loose.I was able to do this originaly when i thought recalibrating the speed would fix my problem but now when i hold down buttons 0,2,and start,release 2, the machine just begins countdown and starts up(for just 17 secs of course)HELP PLEASE!!!


You will probably have to replace the system board. First check power supply to make sure it is giving a constant voltage to the system board. If voltage is variable and/or non constant, than it will need to be replaced. Check the power supply first. Than I would suggest testing each capacitor on the system board for shortage. Also look for any loose solder joints and see if there are any burn marks on bottom of the system board.
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1919 seconds