Guide :Exercise & Fitness : Sole Fitness Package F85 Treadmill & E95 Elliptical with...

EEPROM Error I have an EEprom Error on my Sole E95 Elliptical, does anyone know how to correct the error?

Posted by thejoneses00 on Feb 08, 2009

Research, Knowledge and Information :


Incline Calibration Instructions - Treadmill Doctor


elliptical parts; reviews. ... icon calibration instructions- incline . ... this is a very important step because you will get an error message if this step is skipped.
Read More At : www.treadmilldoctor.com...

Motus USA M990T- M990TL – Treadmill – Troubleshooting – error ...


Motus USA M990T- M990TL – Treadmill – Troubleshooting – error codes ... Trouble in internal EEPROM due to high ... The correct alignment or striding belt is ...
Read More At : electro-medical.blogspot.co.id...

Detail Instructions of Programming EEPROM with Digiprog 3


Detail Instructions of Programming EEPROM with Digiprog 3 V4.94 ... comparing it with the now re-inserted EEPROM; Error message ... reebok r 5.10 elliptical ...
Read More At : www.obd2repair.com...

TREADMILL SERVICE MANUAL - HealthStream


TREADMILL SERVICE MANUAL T560/T561 Customer Support Services ... Er 06 Memory EEPROM of console error, eeprom problem or circuit problem. Frequency is very low.
Read More At : www.healthstream.com.tw...

# Electric Car Battery Swap - How To Charge Rv Battery From ...


Jul 30, 2017 · ... (which contain over 3,000 error code ... Swap How Do I Know If My Battery Is Dead How To ... how much battery life does my computer have:
Read More At : diyreconditionbatteryez.com...

Life Fitness Parts Store | Life Fitness


Life Fitness Parts Store. The best place to get parts for your Life Fitness equipment. ... If you have any questions, call Customer Support at 1.800.351.3737.
Read More At : www.lifefitness.com...

JunoCam and the KAI-2020 Image Sensor - ON Semiconductor


download agreement. important - read before downloading, copying, installing, or using. do not download, copy, install, or use this content until you (the "licensee ...
Read More At : www.onsemi.com...

SONY KDL-40R350C – Service mode – LED blinking code – white ...


SONY KDL-40R350C – Service mode – LED blinking code ... # Select YES if input data is correct. ... Sole Elliptical - E25 - E35 - E55 - E95 – Pin tes...
Read More At : electro-medical.blogspot.co.id...

Suggested Questions And Answer :


Motor error messege on E25 sole ellipticle - RTO Sole Fitness Package F85 Treadmill & E95 Elliptical with Turn Key Delivery Great Savings!


Proceed according. God bless youDescriptionThis error monitors the treadmills power bit reading. Power bits indicate the relative time that themotor controller drive circuit is turned on. Therefore power bits is an indication of the amount ofpower the load is demanding from the motor controller. The treadmill software sets a maximumallowable power bit limit. Error 25 indicates that the maximum power bit limit is being exceeded.Possible Causes1. The running belt and/or running bed is badly worn.2. On treadmills utilizing an SCR motor controller, a leaky or shorted drive motor filter capacitorcould raise the current demand sufficiently to cause the error 25.3. On treadmills utilizing an SCR motor controller, a leaky or shorted drive motor inductor couldraise the current demand sufficiently to cause the error 25.4. A shorted or de-magnetized drive motor is causing the high power demand.Possible Remedies1. A clamp-on A.C. ammeter must be used to determine the amount of A.C input current beingdrawn by the treadmill under no load and loaded conditions. The current readings can beused to determine the condition of the running belt and/or running bed. These same readingsshould be taken on a similar unit with a known good running belt and running bed. Thosereadings can then be used as a benchmark for future use. Replace the running belt and/orrunning bed as required. Remember, many running beds are double sided and the bed canbe flipped over rather than being replaced.2. A clamp-on ammeter should be used to measure the A.C. input current at no load. The filtercapacitor should then be electrically isolated from the drive motor circuit. The drive motorleads must be kept intact so that the drive motor will operate with the filter capacitor removedfrom the circuit. The no load A.C. input current should be measured again, if the A.C. inputcurrent is significantly lower, replace the filter capacitor.3. Use the same procedure as in step 4 above, except remove and isolate the inductor from thedrive motor circuit instead of the filter capacitor.4. A known good drive motor must be substituted for the existing drive motor.
Read More At : Sole Fitness Package F85 Treadmill & E95 Elliptical with......

Operating manual sole e35 - RTO Sole Fitness Package F85 Treadmill & E95 Elliptical with Turn Key Delivery Great Savings!


Go to www.iconservice.com for free downloador http://fitness.manualsonline.comGood luck,sincerely. G-d bless youERNESTO CUADRAMANAGUA,NICARAGUA
Read More At : Sole Fitness Package F85 Treadmill & E95 Elliptical with......

Replace the chain on the stairmaster 4000 pt - RTO Sole Fitness Package F85 Treadmill & E95 Elliptical with Turn Key Delivery Great Savings!


This video should help guide you. Spring Pulley Chain Drive Hub Replacement Video for Stairmaster Stepper...
Read More At : Sole Fitness Package F85 Treadmill & E95 Elliptical with......

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1992 seconds