Guide :Exercise & Fitness : Proform

Motor making noise and slowing down errors E1,E3, and E4

I have a Proform PFTL 20862 treadmill. Until recently working fine. The motor will get the walk up to speed normally but then start making noise and slowing down, speeds up, then slows down until the errors show up on the display. The components on the motor control board get really hot. The motor spins freely without much drag. I'm not sure if it's a problem with the motor or the board. I also need to know where I might find the parts. Thanks, John

Research, Knowledge and Information :

Troubleshooting Treadmill Problems - Treadmill Doctor

Motor Controller Instructions. Mechanical Problems & Tests. Treadmill Drive Motor Installation. Treadmill Roller Instructions. Nordictrack Skier Troubleshooting.
Read More At :

Sole Treadmill Troubleshooting

Sole Treadmill Troubleshooting. ... there are times when problems will arise. Thanks to the lifetime warranty on the motor and the 3-5 year warranty on parts, ...
Read More At :

Indie Personal Finance - Mainstream Money Alternatives

Indie Personal Finance. Mainstream Money Alternatives ... E1 > E2 > (E3 ~= G1) > (E4 ~= G2) ... and there’s no sign of it slowing down.
Read More At :

England's Stove Works | Wood and Pellet Stoves | Heat ...

The official site of England's Stove Works, Inc. Find your favorite Englander, Summers Heat and Timber Ridge wood and pellet stoves (and pellet grills) here. Heat ...
Read More At :

Bosch Washing Machine Error Fault Codes |

BOSCH Washing Machine Error/Fault Codes ... F21 Motor. F23 Anti flood system ... How To Fix A Washing Machine Making Noise During The Spin Cycle July 27, ...
Read More At :

Methods and Practices for Setting Speed Limits: An ...

Methods and Practices for Setting Speed Limits: ... cost of noise caused by motor vehicle operation ... zone speed limit to assist drivers in slowing down. ...
Read More At :

DCC Tips - TrainWeb

There exist several formats of digital command control that are ... possible torque making it more likely that the motor will lug down or ... Motor Noise. To measure ...
Read More At :

1_5302_858_MO_1003%20Asia%20Motor | Fuel Injection | Piston

E3 E4 E5 =Standard ... slowing it down to 2.800 rpm. ... adjusting nut making it closer to the end of the rod 3 to “increase the
Read More At :

Notes on the Troubleshooting and Repair of Small Household ...

Motor bearing problems; Motor noise; ... shows a utility meter slowing down substantially when the Green Plug is ... Hot unwired, other errors ...
Read More At :

Excel Manual | Microsoft Excel | Spreadsheet

Excel Manual - Ebook download as PDF File ... The CD includes a link to Adobe’s Web site, where you can down- load a ... from E3 to E4:E6 the formula MID ...
Read More At :

Suggested Questions And Answer :

Motor making noise and slowing down errors E1,E3, and E4

Kohn This is a controll problem and not a motor problem Replace control panal! only available from the manufactor
Read More At : Proform...

Lifefitness TR 9000 treadmill - 1997 model

Because you are hearing the lift motor making a noise, it sounds like the gears in the motor are bad. The fix is to replace the lift motor.
Read More At : 9000 Next Generation Treadmill...

Proform 400GI Treadmill making a very loud noise, which is worse when using speeds between 2.7 and 3.1, noise is so loud can't hear tv when turned up to full volume. It makes the noise without anyone walking on the treadmill.Is there anything I can check, is it the motor? Thanks V

This definitely sounds like the drive motor. One way to check is to remove the drive belt and run the motor without the walk belt connected. Obviously if you still have the noise it will be a motor issue. If not then it will be one of the 2 rollers. Good Luck! Tim
Read More At : 490GS Treadmill Walking Belt...

I have a proform treadmill that makes a high pitch whirling noise that get louder the faster it goes. Sounds like it is coming from the motor, not the bearings. Suggestions?

Either the drive belt is damaged or the belt is out of alignment due to worn motor shaft bearings.
Read More At : Proform 5.5 Crosstrainer Treadmill Drive Motor...

Proform 730i powers on but will not move when I input speed.

I have the same treadmill with the same problem statement. Here is how I fixed it:....Open the lower shroud that covers the motor. You must remove 4 or 5 screws. Taped to the inside of the shroud should be a document with a calibration procedure on one side and electrical specifications on the other. It will tell you how to run the calibrations. You need to hold the stop button and the + speed button as you insert the safety key. This will put you into calibration mode. My treadmill started working again after I ran the incline calibration routine. Hope this helps.
Read More At : 730 Folding Treadmill Model PFTL71104 - !...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.0931 seconds