Guide :Exercise & Fitness : L7 LTD Executive Trainer Treadmill

Belt does not turn, "safety shutdown, loss of signal" notice

I have a 1999 Landice L7 Executive Trainer treadmill. Recently, while using it, it stopped and I got the message "safety shutdown, loss of signal" Now the belt doesn't move and I can't start the treadmill. Any ideas?

Research, Knowledge and Information :


Problem 7: Other Warning Light(s) On - AutoTap Express DIY


Home > Other Warning Light(s) On. ... will shut down. ... the battery may NOT clear the codes - and may cause a loss of important information that the ...
Read More At : www.autotap.com...

PortableGrainBeltConveyor - batcomfg.com


Safety 2.1. Safety Alert Symbol and Signal Words ... Moving Conveyor Belt Safety • DO NOT step on or touch moving ... before using and know how to shut down in an ...
Read More At : batcomfg.com...

Stalling Recalls - Center for Autosafety


Separation of turn signal/hazard warning signal ... This failure is caused by bearing tolerances which do not ... belt or hose failure, loss of steering ...
Read More At : www.autosafety.org...

PACCAR MX-13 OPERATOR'S MANUAL Pdf Download.


View and Download Paccar MX-13 operator's manual ... Instructions Check Engine Lamp turn off the warning lamp and shut down the ... the belts do not wrap ...
Read More At : www.manualslib.com...

Pro-Turn


SIGNAL WORDS The safety alert symbol above and signal ... DO NOT try to turn or speed up. 2. ... NOTICE: DO NOT cut cable tie. 5.
Read More At : static.allpower.com.au...

M4000-PRO Instructions - BlueBOLT™


The presence of this power signal will turn on the M4000-PRO ... and the M4000-PRO’s shutdown ... prong is provided for your safety. If the provided plug does not ...
Read More At : www.mybluebolt.com...

Pressure Actuated Shutdown for PG Dial and Lever Governors


engine or turbine on either increasing or decreasing signal pressure. Shutdown ... Cutaway View of Loss of Pressure to Shutdown ... Pressure Actuated Shutdown for ...
Read More At : www.woodward.com...

Chevy Recall Information - Chevrolet Recalls and Problems


Chevy Recall Information << Page 1 ... in these states are not subject to this safety recall but may be covered ... does not buckle their seat belt, ...
Read More At : www.lemonauto.com...

Troubleshooting - John Deere


Loose or defective alternator belt. Do not operate at slow idle, ... Fan belt slipping. Loss of refrigerant. ... No right turn signal on the ROPS.
Read More At : manuals.deere.com...

Suggested Questions And Answer :


When I turn on the treadmill, I get a message "Safety Shutdown, Loss of signal"


According to Landice, this is usually an indication of a speed control malfunction. The upper board is not recognizing a signal pickup from the speed sensor. This could be due to the speed sensor being misaligned, improper connection, or bad speed sensor.You need to service it. Or if you are a technical guy, you can use this guide:Landice Service Manual
Read More At : L 7CLUB Executive Trainer Treadmill...

When I turn on I get an overspeed error and machine shuts off. If I start it at a faster speed the speed fluctuates. I pressed start and menu and the LED says 3.5 but the diagnostic reads 6.8


Your speed sensor is not working properly this part is located under the motor shroud and on top of drive motor it is attached to a bracket with 2 bolts. Unplug the unit and remove motor shroud see if you can adjust it first by loosen the 2 nuts and moving the sensor forward without making contact to the flywheel, then tightened the nuts up. Plug the unit into the outlet, start the unit, if you still have the overspeed then replacement of the sensor is needed. Call Landice Directly they will ask for model and serial number and they will the new sensor.
Read More At : L7 LTD Executive Trainer Treadmill...

I need a manual for a carl lewis treadmill - Landice L7 LTD Executive Trainer Treadmill


You can download the Carl Lewis Treadmill manual here
Read More At : L7 LTD Executive Trainer Treadmill...

Landice L9 Treadmill - Loss of Speed Signal Code


At starting, trys to go to speed and then reads LS on screen and runs very slow, with no response to any buttons.
Read More At : L9 Cario Trainer Commercial Treadmill...

Landice L8 treadmill won't turn on - Landice L8 LTD Cardio Trainer Treadmill


Check wall outlet for power , then if outlet is good unplug unit remove motor shroud you will see a charcoal or white ceramic fuse check it if open replace blows again immediately you have a shorted lower board. Here is the info Landice they help you with parts and get you in touch with a servicer if you need one. Landice, Inc.111 Canfield AvenueRandolph, New Jersey USA 07869(800) LANDICE(973) 927-9010 - FAX: (973) [email protected]
Read More At : L8 LTD Cardio Trainer Treadmill...

Carl lewsis ctm003 manual - Landice L7 LTD Executive Trainer Treadmill


PLEASE go to www.fitness.manualsonline.com and download for free.God bless you
Read More At : L7 LTD Executive Trainer Treadmill...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0985 seconds