Guide :Exercise & Fitness : Image 17.5 S Treadmill

Treadmill incline drive stuck up & down

When I turn it on, the incline motor drives it up & down and will not stop.

Research, Knowledge and Information :


Incline Motor Problems - Treadmill Doctor


Incline Motor Problems. The most common symptoms we hear about are that the incline is just running up and/or down and the treadmill won ... the drive motor as normal ...
Read More At : www.treadmilldoctor.com...

3 Easy Ways to Fix a Treadmill (with Pictures) - wikiHow


How to Fix a Treadmill. ... before you begin the repair. If your treadmill speed control is a digital display/button that you press to speed up/down, ...
Read More At : www.wikihow.com...

our nordic track commercial 1500 treadmill is stuck at 12%


Our nordic track commercial 1500 treadmill is ... 1500 treadmill is stuck at 12% incline and although ... it is stuck, continue to move up, and down and ...
Read More At : www.justanswer.com...

Treadmill incline stuck up - Amazon Web Services


The larger the discrepancy between the two, the just keep moving than slowing treadmill incline down stuck up to walk. Without resting intervals, you will not be ...

Have a ProForm 745cs treadmill. The incline/decline motor no


Have a ProForm 745cs treadmill. The incline ... I thought it got stuck in the highest incline position so I ... but ONLY WHEN THE INCLINE UP OR DOWN ARE ...
Read More At : www.justanswer.com...

Shuts Down During a Workout - Treadmill Doctor


If you can walk on your treadmill but it shuts down ... Put the treadmill at full incline and ... you can restart it back up but it shuts down faster and the ...
Read More At : www.treadmilldoctor.com...

How to Fix Common Treadmill Problems 2017 | TreadmillReviews.net


How to Fix Common Treadmill Problems. ... If the machine shuts down, ... Too much friction on the running belt can cause the belt to heat up and not run properly.
Read More At : www.treadmillreviews.net...

SportsArt – 8100 Elliptical Trainer – Incline Calibration Guide


SportsArt - 8100 Elliptical Trainer - Incline Calibration Guide Introduction An incline motor, like those in treadmills, makes the 8100 ramp up and down.
Read More At : www.sportsartamerica.com...

Suggested Questions And Answer :


Image 17.0 Treadmill is stuck in incline position and will not go down. I do not plan to use the include at all, is there a manual way to move the incline to 0? Any suggestions?


Hello there, The first thing I would try is to calibrate the incline on the unit. Do this using the following procedure. With the safety key out, press the stop button along with the speed up button while inserting the safety key onto the unit. remove your fingers from all buttons, Then press the stop button one time. Now press the incline up button one time. The unit should go all the way to the top, then return to the bottom. Remove the safety key and reinsert it to continue using the machine If this does not work you can manually move the machine to the bottom using this procedure. Remove the hood cover b removing 2 screws in the rear of the machine and removing the first 2 screws on the foot rails on each side. You can now lift the cover out of the way. At this point you will see the incline motor located in the center of the unit pointing in a downward direction. On the top of the motor there will be a small fan encased inside of a metal cover. There will be a flat head screw located inside the metal frame where the fan is. Rotate this clockwise to lower the unit. (the motor is geared very high it may not seem as though it is moving but it is) be patient that procedure does take a little while. Any questions please feel free to leave another message on this link. Good Luck! Tim
Read More At : Image 17.5 S Treadmill...

The treadmill is stuck on "incline." Any time we put the red key on it to turn it on, it just keeps moving up and down from 0 incline to 10. It does this over and over again without stopping. No buttons respond.


I can't solve this, but my Nordic Track T5 zi occasionally does the same thing. The previous two times, I waited until the unit "bottomed out", and then pulled the mag switch (key) off. I unplugged the unit, then plugged it back in, attached the key, and all was well. This worked twice before, but today (3/8/2011)the unit's incline is cycling again, and the old fix isn't working. Maybe it will need to go back to Sears! Unit was purchased in October of 2010. Frustrating.
Read More At : NordicTrack T5 zi Treadmill...

Tempo 621T treadmill stuck in incline postion scale is reading 0 but it is not completely down..How to reset my incline button


Run the software calibration for troubleshooting and fix it. See the next steps. God bless you The Steps for Newer Style Console Calibration Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.) Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed). Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E." Press ENTER. You should see "SS" or "55" in the console. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step. Lube the elevation motor, shaft and gear. adjust the POTentiomer,
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0877 seconds