Guide :Exercise & Fitness : Stepmill 7000 Pt

Stepmill 7000 wont regulate speed

Stairs turn faster and faster. The led field light goes off when stairs are started

Research, Knowledge and Information :


Speed Control Problems - Stairmaster STEPMILL 7000 Owner's ...


Stairmaster STEPMILL 7000 Manual Online: Speed Control Problems. Page 33...
Read More At : www.manualslib.com...

STEPMILL 7000 OWNER S ANUAL - support.stairmaster.com


This is to certify that the StairMaster® Stepmill® 7000 PT exercise system is ... Speed Control Problems ...
Read More At : support.stairmaster.com...

The Stairmaster Stepmill 7000PT.


The Stairmaster Stepmill 7000PT. "Uses a revolving staircase which can vary in speed enabling the machine to simulate walking ... the Stairmaster Stepmill 7000 PT, ...
Read More At : stairmaster7000pt.com...

Stairmaster: Stair Machines & Steppers | eBay


The speed control buttons allow for an increase or decrease the stepping speed at any ... You won't find one better ... The StairMaster® 7000 PT StepMill® is ...

STEPMILL 7000 OWNER S ANUAL - nautilusgsa.com


include the Stepmill® 7000 PT – for the ... Stepmill exercise system should fail to operate properly ... The Speed Test ...
Read More At : www.nautilusgsa.com...

StairMaster 7000 PT Stepmill – Fitness Factory


StairMaster 7000 PT Stepmill ... The Stairmaster Stepmill 7000PT uses a revolving staircase which can vary in speed enabling the machine to simulate walking or ...
Read More At : www.fitnessfactory.com...

StairMaster 7000 PT Stepmill - amazon.com


The stair master stepmill 7000PT uses a revolving staircase which can vary in speed enabling the ... muscle workout with the StairMaster 7000 PT stepmill ...

STAIRMASTER STEPMILL SM916 OWNER'S MANUAL Pdf Download.


View and Download StairMaster StepMill SM916 owner's ... allows you to control the step rate of the StepMill ® SM916 ... with the speed of the ...
Read More At : www.manualslib.com...

Suggested Questions And Answer :


Stepmill 7000 wont regulate speed


Check the blue wire to the alternator. Check all connections. the blue wire is the tach wire. no tach signal and you cant climb fast enough!
Read More At : Wide Ride Pedal...

Stepmill 7000 wont regulate speed


Just clean and rebuild or simply resoldered all parts joints in the circuit board so the parts connectivity renew so it function very well and most of all, if you see a capacitor there replaced it all. Maybe that is the caused of the stepmill not to regulate or function normally.The function of the capacitor is to hold the voltage if the capacitor is leaky already it will not hold the voltages causing the machine to function abnormally .I experienced like this capacitor problem when I repair an escalator before,its function abnormally its cannot be regulated.I did the procedure i said above and replaced all the capacitor its works find its run normally. Hope it may help you; Regards; VOTIT
Read More At : Stepmill 7000 Pt...

No speed up on stairmaster stepmill 1994 model


This link will take you to some information on various resistance issues on the SM916
Read More At : StairMaster SM916 StepMill...

Reebok 8100 es wont go any faster then .4mph


Please adjust the speed sensor, see the diagram, test it for open or faulty, clean it, and tight the plug very well.However you must RUN the software calibration for easy diagnose, and troubleshooting and fix it. Go under HOOD motor, and follow the steps .God bless you
Read More At : Exercise & Fitness...

Itook my startrac pro s treadmill apart to move it from downstairs to upstairs in house. The wire running from bottom circuit board to display console got strained and bent two condensers on circuit board,Had these replaced.Treadmill now runs for 17 seconds at idle speed,3 seconds if you try to increase speed and then stops.Displays message"CHECK SPEED SYSTEM".Had speed sensor at flywheel and wire which was strained tested,which were both o.k.I Took cover off back of display console,nothing seems to be bent or broken that i can see,i also followed the steps for recalibrating the speed to no avail either.Before i had the condensores replaced the machine would not work at all it just made clicking noises.thats all the info. i can give. Please please HElp!!!Since posting this problem i've had some very good advise from one of your experts (blueextc) but i cant seem to make contact with him,in order to carry out his advise i need to enter maintenence mode and there in lies my latest problem,i cant gain access.I've checked all connections and nothing appears loose.I was able to do this originaly when i thought recalibrating the speed would fix my problem but now when i hold down buttons 0,2,and start,release 2, the machine just begins countdown and starts up(for just 17 secs of course)HELP PLEASE!!!


You will probably have to replace the system board. First check power supply to make sure it is giving a constant voltage to the system board. If voltage is variable and/or non constant, than it will need to be replaced. Check the power supply first. Than I would suggest testing each capacitor on the system board for shortage. Also look for any loose solder joints and see if there are any burn marks on bottom of the system board.
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0369 seconds