Guide :Exercise & Fitness : Wide Ride Pedal

Stepmill 7000 wont regulate speed

I have a stepmill 7000 that I can not regulate speed, it seems to grab momentarily then keeps speeding up until you cant keep up

Research, Knowledge and Information :


Speed Control Problems - Stairmaster STEPMILL 7000 Owner's ...


Stairmaster STEPMILL 7000 Manual Online: Speed Control Problems. Page 33...
Read More At : www.manualslib.com...

STEPMILL 7000 OWNER S ANUAL - nautilusgsa.com


include the Stepmill® 7000 PT ... Stepmill exercise system should fail to operate properly ... Speed Control Problems ...
Read More At : www.nautilusgsa.com...

STEPMILL 7000 OWNER S ANUAL - support.stairmaster.com


This is to certify that the StairMaster® Stepmill® 7000 PT exercise system is ... Speed Control Problems ...
Read More At : support.stairmaster.com...

The Stairmaster Stepmill 7000PT.


The Stairmaster Stepmill 7000PT. "Uses a revolving staircase which can vary in speed enabling the machine to simulate walking ... the Stairmaster Stepmill 7000 PT, ...
Read More At : stairmaster7000pt.com...

StairMaster 7000 PT Stepmill – Fitness Factory


StairMaster 7000 PT Stepmill ... The Stairmaster Stepmill 7000PT uses a revolving staircase which can vary in speed enabling the machine to simulate walking or ...
Read More At : www.fitnessfactory.com...

StairMaster 7000 PT Stepmill - amazon.com


The stair master stepmill 7000PT uses a revolving staircase which can vary in speed enabling the ... muscle workout with the StairMaster 7000 PT stepmill ...

STAIRMASTER 7000PT Stepmill Parts - sportsmith.net


46 sm23591 assy,speed reducer,stepmill,sv ns sm22869 manual 7000tp c-40 ... 48 sm22434 assy,speed reducer,7000 pt,sv ns sm24381 power supply,ps-7,3-pin
Read More At : www.sportsmith.net...

STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS - support.stairmaster.com


stepmill 7000 pt assembly instructions part number 27698. 2 assembly instructions tools required: •knife •2-9/16” wrenches •5/32” allen wrench 1.
Read More At : support.stairmaster.com...

Suggested Questions And Answer :


Stepmill 7000 wont regulate speed


Check the blue wire to the alternator. Check all connections. the blue wire is the tach wire. no tach signal and you cant climb fast enough!
Read More At : Wide Ride Pedal...

Stair Climbers screen won't work


Wide Ride Pedal CTGID0 Stair Climbers screen won't work
Read More At : Wide Ride Pedal...

Stepmill 7000 wont regulate speed


Just clean and rebuild or simply resoldered all parts joints in the circuit board so the parts connectivity renew so it function very well and most of all, if you see a capacitor there replaced it all. Maybe that is the caused of the stepmill not to regulate or function normally.The function of the capacitor is to hold the voltage if the capacitor is leaky already it will not hold the voltages causing the machine to function abnormally .I experienced like this capacitor problem when I repair an escalator before,its function abnormally its cannot be regulated.I did the procedure i said above and replaced all the capacitor its works find its run normally. Hope it may help you; Regards; VOTIT
Read More At : Stepmill 7000 Pt...

Stair climbers / steppers maintenance


" * Read all maintenance instructions thoroughly before beginning work. * In some cases, an assistant is required to perform the necessary tasks, use all precautions. * The safety level given by the design of this equipment can only be maintained when the equipment is regularly examined for damage and wear. * Inoperable components should be replaced immediately or the equipment should be put out of use until it is repaired."
Read More At : Wide Ride Pedal...

Screeching stair climber


Wide Ride Pedal CTGID0 Screeching stair climber
Read More At : Wide Ride Pedal...

Stair stepper won't start


Wide Ride Pedal CTGID0 Stair stepper won't start
Read More At : Wide Ride Pedal...

What can i do if the steps are continuously going in a non-consistent pace?


Hi drlinders,   You could hardly find any expert who deals with all this. More likely, you would not be able to find any information in outer world ( Internet ) regarding the same.  The best advise would be to purchase a new one.A new wide ride pedal would cost you  $32.99.You can purchase it from amazon.com http://www.amazon.com/Schwinn-Wide-Ride-Pedal-2-inch/dp/B000F5NKZM Even if you contact the schwinn, more likely this would be the same advise from them.  I know its really frustrating, but it seems to be the best solution at this moment. Thanks for using Fixya.
Read More At : Wide Ride Pedal...

No speed up on stairmaster stepmill 1994 model


This link will take you to some information on various resistance issues on the SM916
Read More At : StairMaster SM916 StepMill...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0695 seconds