Guide :Exercise & Fitness : NordicTrack Treadmill, A2550

Title: Treadmill Belt Problem

My belt is offcentered and threads are raveling on side.

Research, Knowledge and Information :

Walking Belt Problems - Best Treadmill | Treadmill Doctor

All of the major components of your fitness equipment are for sale on our website, from motors and belts to wheels and treadmill keys. However, if you can't find what ...
Read More At :

How to Fix Common Treadmill Problems 2017 |

How to Fix Common Treadmill Problems. ... Try to lubricate the belt to see if the problem is fixed. Ultimately, the belt may need to be replaced.
Read More At :

Troubleshooting Treadmill Problems - Treadmill Doctor

Walking Belt Problems. Walking Belt Tests and Adjustments. ... Our treadmill mats provide the proper foundation for your elliptical or treadmill and protect your floor.
Read More At :

Ten Common Treadmill Running Problems | RunAddicts

The decision to buy a treadmill is usually good one. These devices can provide you with the flexibility of exercising in your own home. This can allow you to get in ...
Read More At :

How To Fix A Slipping Treadmill Belt - YouTube

Mar 20, 2014 · I show how to repair a treadmill walking belt that slips or stops sometimes when your foot comes down as you are running or walking. The most common ...

The Airplane-Treadmill Problem -

The airplane-treadmill problem is a physics thought experiment that has become a minor internet meme. ... On a small conveyor belt ...
Read More At :

Treadmill - Wikipedia

Injury to children can be avoided by removing the safety key when the treadmill is not in use, without which, the treadmill belt will not start.
Read More At :

What are some common treadmill problems? |

Common treadmill problems include speed changes, slipping belts, overheated belts, no display and a burning odor. The owner should fix the problem as soon as possible ...
Read More At :

How to Fix the Top 5 Treadmill Problems

The following are a list of the top 5 treadmill problems that can be fixed by the ... you will have to replace the walking belt. When buying a treadmill for home ...
Read More At :

Suggested Questions And Answer :

Recumbant bike slips while peddling

Http:// Loose Pedals 1 Kneel next to the left side of the elliptical's base. Use the Phillips screwdriver to tighten the two screws located in the center of the left pedal. 2 Use the Allen wrench to remove the bolt securing the left pedal arm to the pedal leg and body arm. Use the Phillips screwdriver to remove the screw securing the rear end of the pedal leg to the crank arm. 3 Pull the end of the pedal leg free of the crank arm. Wipe the crank arm clean, then apply a fresh coating of machine grease or silicone lubricant. Replace the end of the pedal leg back onto the crank arm and use the previously removed screw to secure it back into place. 4 Join the front end of the left pedal arm to the ends of the pedal leg and body arm. Use the previously removed bolt to connect the pieces together. 5 Move to the right side of the elliptical and repeat the above steps on the right pedal arm.
Read More At : NordicTrack Treadmill, A2550...

Nordictrack EXP 1000 Treadmill Quits after 10 Minutes

Hello There, Thank you for all the information. It appears as if your walk belt is worn. What is happening is the friction from the bottom of the belt is actually causing the motor to overheat (there is a thermal cutout inside where the 2 blue wires go) When the belt wears the cloth on the underside becomes flattened out causing too much surface area to contact the walk board, thus the extra friction. To check your walk board you can loosen the adjusting bolts on the rear and while lifting the walk board look underneath. If there is any wear/white areas then you will need to replace the board as well. You will be able to tell by just rubbing your hand across it and check for any places where the black film may be coming off. Also the only time you really need to replace any of the rollers is when the bearings go bad or the pulley on the front roller separates. The rollers are about a 1% chance of causing this problem. Good Luck! and great question, Tim
Read More At : NordicTrack...

Nordictrack exp 1000 trips safety and stops abruptly...

Inspect belt and deck. The deck should be smooth without any grooves, pits, or exposed wood. The belt should have a consistent ridged feel from one side of the belt to the other (a belt can be worn out without any sensory signs of a problem). If you feel deep grooves in the deck or uneven wear on the underside of the belt, part replacement is necessary. Visually look at the underside of the belt. It should have a consistent look. Black streaks in the belt are a sign of bottom-layer wear through. Very worn belts will feel smooth in the areas you normally walk- you would think smooth is good but not in belts because the smoother the belt, the more contact area. Continued use of your treadmill may damage expensive electrical components. 85% of all Treadmill problems are cause by worn belt and deck I would revisit the scene of the crime again.
Read More At : Nordic Track...

Treadmill Incline Works, belt does not move

Check the drive belt. It may be loose or broken. If the belt is loose, then to tighten the drive belt, start by removing the front cover. loosen the bolts around the motor then tighten the drive belt by tightening the motor adjuster bolt. Once the drive belt is tight, tighten the motor back down.
Read More At : NordicTrack A2350 Pro Treadmill...

Nordictrack C2050, belt was slipping and I got the cover off. and black stuff is all around the belt moving the roller that moves the treadmill. When I walk on it the belt would shuffle and sometimes the roller would stop. What do I need to order? I probably need the belt that makes the roller go and dont know if I need the pully to help the roller go?

I am not an expert on what you may need to order but I do want to give you a link in case that may be helpful... has parts lists for several versions of the C2050... look for a decal or label on the machine to get the exact model number, then click on that model and look in the list for 'Roller, Front' or 'Roller, Rear' or 'Treadbelt.' Hope that helps.Also if you need someone to come look at it you can find a list of servicers near you here
Read More At : NordicTrack Treadmill, A2550...

While using my Nordictrack a2550 this morning, the walking belt began to slip very badly. I checked the alignment and adjusted the tension of the belt as per the user's manual but the belt stills slip very badly. Please help.

If it really is the walking belt that is slipping keep tightening the adjustment screws till the belt will not slip when you try to stop it ( set speed to about 3 and then with your foot try to stop belt from spinning - you should be able to make the motor and whole machine come to a stop ) make sure it is really walk belt spinning and it isnt the motor belt slipping. (if it is motor belt slipping when you try to do the stop the belt trick i just described you will see the walk belt and front roller stop but still hear the motor turning) once you get walk belt tight enough so it doesnt slip then you can worry about keeping the belt centered. let me know if you need more help on this and let me know how the stop the belt test went good luck!
Read More At : NordicTrack A2550 PRO Treadmill...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.1494 seconds