Guide :Exercise & Fitness : L7 LTD Executive Trainer Treadmill

When i start my l7 it trys to start then stops and the display reads PO

Posted by mikelsu12 on Nov 10, 2010

Research, Knowledge and Information :

We would like to show you a description here but the site won’t allow us.
Read More At :

Torrentz Search Engine

Torrentz will always love you. Farewell. © 2003-2016 Torrentz
Read More At :

Mercedes Benz Fault Code Manual | Throttle | Fuel Injection

Mercedes Benz Fault Code Manual ... Also if you start diagnosing a ... 6. press the "RECIRCULATE AIR" button after each is displayed until the display reads ...
Read More At :

Then start where U. S. citizens ... will make stops In Orlando However a communique announced 500 students for the first t head to let the ... Post Office tins 1MT
Read More At :

Notes: Additional Physical Form: Also available on microfilm from the University of Florida. Dates or Sequential Designation: Vol. 9, no. 41 (Apr. 13, 1888)-
Read More At :

1983 Gem of the Mountains, Volume 81 - University of Idaho ...

Large display racks of Garfield novelties domlnated ... finds Idaho very beautiful. "Since this is my first ... The campus post office houses the mail boxes of ...
Read More At :

Educate Magazine by Mersey Mirror - issuu

Title: Educate Magazine, Author ... in the UK are considered obese before they start ... trys out her new bike A year four pupil has been ...
Read More At :

Art Journal 45 3 Video the Reflexive Medium | Modernism ...

The serial presentation of "just facts" is then amplified by ... the start Duchamp set up a vertigo of delay ... from Zen Buddhism and the Huang Po Doctrine of ...
Read More At :


i can't even see the kubuntu logo at start up ... my fstab reads UUID=4701-C88B /0moon ... go to system settings and then click monitor and display then click ...
Read More At :

Full text of "73 Magazine (May 1963)" - Internet Archive

Full text of "73 Magazine (May 1963)" See other formats ...
Read More At :

Suggested Questions And Answer :

When i start my l7 it trys to start then stops and the display reads PO

Refer to page 7 of the diagnostic manual. That means POT out error. It will give you the steps on page 7 for troubleshooting this error: you need further assistance please let me know.Thank you,Lee
Read More At : L7 LTD Executive Trainer Treadmill...

I have a ten year old lightly used Landice L7 treadmill. A couple of years ago it started clicking when turned on and took 3-5 minutes before the belt started moving. After it was moving I had to wait a few minutes more before starting to walk on it as it would stop if I got on it too soon. Yesterday it started the same but it clicked for about 7-8 minutes then the belt would start to move and almost immediatly stop with a message about the elevation. I tried it a few times and finally the belt stared turning and ran for about 30 seconds and quit with a message about the speed. Today The belt doesn't even start turning.

Hello CaptJack. Your treadmill is need of a major tuneup. Contact landice at They will be able to direct you to their nearest service center.....or you might ask them if they take turn-ins against rebuilt models........... Regards, Joe
Read More At : L 7CLUB Executive Trainer Treadmill...

Landice L8 Cardio trainer giving messages on readout P4 and L5

I've definitely never seen "P4" on a Landice before so I'm not entirely sure on that one. The other issues seem like they might be associated with stuck keys on the console. It's a very common problem if you have it in a humid area and/or it gets sweat on it during the work out. Being that it's a Landice, you should have a part warranty on it. Have you contacted them?
Read More At : L 7 Club Cardio Trainer Treadmill...

Landice executive L8 treadmill makes clunking noise when I run on it

You need to get someone out to look at it. Noise issues are rarely able to be diagnosed remotely.
Read More At : L8 80 LTD Executive Trainer Treadmill...

Landice L7 treadmill won't turn on

1)LUBE the deck belt, maybe you have a deck belt worn, by lack maintenance.2) Lube the rollers bearings, in according with the maintenance schedule.3) Test the main motor for voltage input, if there are the motor need repair.4) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty.5) After fixing RUN the software calibration for diagnose, and troubleshooting.
Read More At : L7 Executive Trainer Treadmill Fitness Running Walking......

Proform 550xp Treadmill in continuous incline/decline mode!!!

I just called the manufacturer on this and found out i have a faulty control panel, but these are the steps they told me to go through to reset. If it works, then you are good, if not, you may also have a control panel issue.1. plug in and turn on treadmill, keep red key out2. press and hold the stop button and speed up button at the same time and hold them while you insert the red key3. after red key is inserted, let go of both buttons**CAUTION - be sure to stand on side bars of treadmill, clear of the belt for this next part bc it will go VERY FAST***4. press stop button once5. press speed up button until it reads 85 (see what i mean?!)6. press stop button once7. press incline down or up one time and it should get back into normal mode. mine just started a series of flashing lights and "8"s in all the "windows" so my panel needs to be replaced. here is the number i called - 1-877-993-7999. Good Luck!
Read More At : Exercise & Fitness...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || || Terms of Use || Contact || Privacy Policy
Load time: 0.1772 seconds