Guide :Exercise & Fitness : Bodyguard T300 Commercial Treadmill

Treadmill incline works, belt does not move

I have a Reebok ACD2 treadmill.  When I insert the key, all the lights go on and the incline works fine.  However, when I press start to move the belt, it does not move, but the readout says that I am moving at a certain speed - whatever it was set to (1mph, 2mph, etc)  Any thoughts about what might be wrong.  I just moved and it was working before the move.  Could something have been broken in the move?  Thanks.

Research, Knowledge and Information :


3 Easy Ways to Fix a Treadmill (with Pictures) - wikiHow


How to Fix a Treadmill. ... Do not work on a treadmill while it is connected to a power source. You could be electrocuted or the treadmill belt could begin to move ...
Read More At : www.wikihow.com...

Hi I have a Horizon treadmill. The belt on it will not move


How JustAnswer Works: ... Hi I have a Horizon treadmill. The belt on it will not move round, ... Even though you can not get it to move, does the incline work?
Read More At : www.justanswer.com...

The Treadmill Belt Won't Move | LIVESTRONG.COM


Sep 10, 2015 · The Treadmill Belt Won't Move. ... A treadmill belt can shift to the right or left ... You may void the warranty if you attempt to work on the motor ...
Read More At : www.livestrong.com...

I need treadmill help! Proform xp 550e. Belt won't move...but ...


Jan 03, 2014 · Absolutely everything works with this treadmill except the motor wont turn over. But it will turn when hooked up to a 18v battery. Any suggestions? Incline ...

Incline Motor Problems - Treadmill Doctor


Incline Motor Problems. ... if that is the problem and then reinstalling it in the treadmill will get it to work. ... If the incline motor does not move, ...
Read More At : www.treadmilldoctor.com...

Proform treadmill will not run | Sears PartsDirect


Proform treadmill will not ... and it still didn't work,so then I checked the power ... belt does not move but the incline will still go up and down ...
Read More At : www.searspartsdirect.com...

Treadmill Troubleshooting - NordicTrack


If this does not work or your console does ... Move the tip of the reed ... The belt stops when I'm walking on the treadmill. If the belt starts again ...
Read More At : service.nordictrack.com...

Exercise Equipment Troubleshooting | Horizon Fitness


All or some of the keys on the console do not work. ... Incline motor issues Unplug the treadmill from the outlet. ... My running belt does not move.
Read More At : www.johnsonfit.com...

Suggested Questions And Answer :


Bodyguard t300 treadmill. belt will not turn


Smashed harness created short.
Read More At : Bodyguard T300 Commercial Treadmill...

Nordictrack Commercial 1500 treadmill w/working display BUT unresponsive buttons


Sounds like a cable harness is undone. The cable feeding the panel which has the computer inside (the power feed) is connected, but the cable from the panel back to the motorized parts isn't. The breakaway is a separate circuit that cuts all power to everything. These are my assumptions (I'm not a nordic track expert), but it's a pretty safe bet, likely the connector in the bottom section. Okay, I just looked it up, first Google "nordictrack 1500 manual" one of the first links is a PDF, with a complete parts breakdown. Depending on your specific model, it looks like there is a connector under the top panel where it meets the right post (and a couple of screws will let you lift it up to check it). It may be partially unplugged, check that first since it looks pretty easy to check. But I think it's going to be in the bottom, in the bottom of the treadmill the wiring splits to different sections. The motor/incline controller cable (a separate cable #106 on one model I looked up, something like NTL09707 or similar) is probably the one that is either broken or unplugged. So although the computer (up top) is sending signals, they aren't reaching where they need to. Anyway, get that manual, and someone handy with screwdrivers and technology, and they should have it figured out quickly.
Read More At : NordicTrack Commercial 1500 Treadmill...

Treadmill Incline Works, belt does not move


Check the drive belt. It may be loose or broken. If the belt is loose, then to tighten the drive belt, start by removing the front cover. loosen the bolts around the motor then tighten the drive belt by tightening the motor adjuster bolt. Once the drive belt is tight, tighten the motor back down.
Read More At : NordicTrack A2350 Pro Treadmill...

Just replaced the motor controller on my treadmill (Nordic Track Commercial 1500) but it still does not generate any speed to the belt. I still have power. Display works fine, incline works find, just that belt does not move. Any ideas?


You have one of three things wrong. Either a bad console, bad motor or a bad wiring harness. If you have a flashing light on the controller when you attempt to start the machine then you more than likely have a bad motor. (this has a long warranty may be able to get one for free, check the back of your manual) If there is no flashing light on the console then you will need to check the wire harness. This unit is known for pinching wires at the lower section where the upright connects to the lower frame. To check this you will need to remove the console. Three screws on each side and the wire harness on the right side will need to be unplugged. Then remove the right upright by removing the two bolt located on the bottom of the frame. Then do a visual inspection for pinched wires especially where the upright connects to the lower frame. If the harness looks ok then you will more than likely have a bad console. If you need parts you can go to http://www.iconservice.com/CustomerService/parts.do Good Luck! Tim
Read More At : Icon...

Nordictrack COmmercial 1500 console buttons don't work


Http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnessincerely. Please keep me in touch.
Read More At : NordicTrack Commercial 1500 Treadmill...

My T81 treadmill quit working. All of the lights and bells and whistles all work but the belt doesnt move and the incline doesnt move. Ive only had it for about 2 years. It was working fine before I moved it across a few states. When I unpacked it and turned it on the lights and fan and sounds all came on but the belt wont turn and the incline doesnt go up or down.


You need to check voltage going to the motors. no power ,the contoller board is not working. check the connections on the boardmake sure they are in all the way,also the power connections
Read More At : T91 Treadmill...

Unit powers on but belt won't move (motor problem?)


You problem is with the motor controller. If everything works but belt want turn 99% of the time it's the motor controller. Call if you'd like more information. 404.456.2327
Read More At : /proform Treadmill Drive/motor Belt 118016...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.fitness-equipment-plus.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1313 seconds